- Illuminates when ignition switch turned ON
- Warning light comes on when the power switch on (READY) (for HV Model).
- Turns off when engine started (for Gasoline Model)
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000021IMV |
| Model Year Start: 2022 | Model: RAV4 | Prod Date Range: [12/2021 - ] |
| Title: METER / GAUGE / DISPLAY: METER / GAUGE SYSTEM: OPERATION CHECK; 2022 - 2024 MY RAV4 RAV4 HV [12/2021 - ] | ||
OPERATION CHECK
CHECK COMBINATION METER ASSEMBLY
(a) Check speedometer operation
NOTICE:
- The combination meter assembly receives the vehicle speed signal from the brake actuator assembly (No. 2 skid control ECU)*1 or brake actuator assembly (skid control ECU)*2 via CAN communication. Therefore, perform the following inspection referring to values on the Data List of the brake actuator assembly (No. 2 skid control ECU)*1 or brake actuator assembly (skid control ECU)*2 because it is the source of the vehicle speed signal.
- Data List values of the brake actuator assembly (No. 2 skid control ECU)*1 or brake actuator assembly (skid control ECU)*2 are used for this inspection. Therefore, make sure to perform this inspection after confirming that DTCs are not output.
- *1: for HV Model
- *2: for Gasoline Model
(1) Warm up the engine.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to ON.
(4) Turn the Techstream on.
(5) Put the engine in inspection mode (maintenance mode).
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; INTRODUCTION: REPAIR INSTRUCTION: INSPECTION MODE PROCEDURE](/t3Portal/stylegraphics/info.gif)
(6) for HV Model:
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
Chassis > ABS/VSC/TRAC
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Vehicle Speed |
Maximum wheel speed sensor reading |
Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) |
Almost same as actual vehicle speed Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
Chassis > ABS/VSC/TRAC > Data List
|
Tester Display |
|---|
|
Vehicle Speed |
(7) for Gasoline Model:
Chassis > Brake/EPB > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Vehicle Speed |
Maximum wheel speed sensor reading |
Min.: 0 km/h (0 mph), Max.: 6553.5 km/h (4072.34 mph) |
Almost same as actual vehicle speed Vehicle stopped: 0 km/h (0 mph) |
When driving at constant speed: No large fluctuations |
Chassis > Brake/EPB > Data List
|
Tester Display |
|---|
|
Vehicle Speed |
(8) Read the Data List according to the display on the Techstream.
Reference mph
|
Techstream Indication (mph) |
Acceptable Range (mph) |
|---|---|
|
20 |
19.5 to 22.0 |
|
40 |
40.1 to 42.9 |
|
60 |
60.8 to 63.6 |
|
80 |
81.3 to 84.5 |
|
100 |
102.1 to 105.3 |
|
120 |
122.8 to 126.0 |
|
140 |
143.5 to 146.7 |
Reference km/h
|
Techstream Indication (km/h) |
Acceptable Range (km/h) |
|---|---|
|
20 |
18.7 to 22.7 |
|
40 |
39.3 to 43.8 |
|
60 |
60.0 to 64.5 |
|
80 |
80.4 to 85.4 |
|
100 |
101.2 to 106.2 |
|
120 |
121.9 to 126.9 |
|
140 |
142.6 to 147.6 |
|
160 |
163.4 to 168.4 |
|
180 |
184.1 to 189.1 |
|
200 |
204.8 to 209.8 |
|
220 |
225.6 to 230.6 |
OK:
Speedometer reading is within the acceptable range at each vehicle speed.
(b) Check tachometer (for Gasoline Model)
(1) Warm up the engine.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to ON.
(4) Turn the Techstream on.
(5) Put the engine in inspection mode (maintenance mode).
Click here
(6) Enter the following menus: Powertrain / Engine Control / Data List.
(7) Read the Data List according to the display on the Techstream.
Powertrain > Engine > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Engine Speed |
Engine speed |
Min.: 0 rpm, Max.: 16383 rpm |
Actual engine speed |
- |
Powertrain > Engine > Data List
|
Tester Display |
|---|
|
Engine Speed |
OK:
Tachometer reading is within the acceptable range at each engine speed.
Reference:
|
Techstream Indication (rpm) |
Acceptable Range (rpm) Data in ( ) is for Reference |
|---|---|
|
700 |
630 to 770 |
|
1000 |
(900 to 1100) |
|
2000 |
(1850 to 2150) |
|
3000 |
2800 to 3200 |
|
4000 |
(3800 to 4200) |
|
5000 |
4800 to 5200 |
|
6000 |
(5750 to 6250) |
|
7000 |
6700 to 7300 |
|
8000 |
(7700 to 8300) |
(c) Check LED illumination (LED check)
(1) Check the illumination function of the warning or indicator lights listed below when turning the ignition switch to ON.
|
Indicator/Warning Light |
Switch Condition |
Specified Condition |
|---|---|---|
|
Brake warning light |
Ignition switch off → ON |
Comes on for 3 seconds |
|
ABS warning light |
||
|
Slip indicator light |
||
|
VSC OFF indicator light |
||
|
PCS OFF warning light |
||
|
RCTA OFF indicator light |
||
|
Brake hold standby indicator light |
||
|
Brake hold operated indicator light |
||
|
Tire pressure warning light |
||
|
SRS warning light |
Ignition switch off → ON |
Comes on for 6 seconds |
|
EPS warning light |
Ignition switch off → ON |
|
|
MIL (Check engine warning light) |
CHECK ENGINE OIL PRESSURE WARNING
(a) Using the Techstream, according to the display on the Techstream, enter "Inspection Mode".
Click here
(b) Disconnect the connector of the engine oil pressure switch assembly.
(c) Start the engine.
(d) Using SST, check the display of the combination meter assembly when connecting the vehicle wire harness side connector terminal of the engine oil pressure switch assembly to the body ground.
SST: 09843-18040
OK:
"Oil Pressure Low Stop in a Safe Place See Owner's Manual" is displayed on the multi-information display.
CHECK ENGINE OIL LEVEL WARNING
(a) Using the Techstream, according to the display on the Techstream, enter "Inspection Mode".
Click here
(b) Start the engine.
(c) With the engine warmed up (coolant temperature 80°C [176°F] or higher) and after 40 seconds or more have elapsed with the engine speed at 1200 rpm or less, check the multi-information display on the combination meter assembly with the engine oil level sensor connector disconnected.
OK:
"Engine Oil Level Low Add or Replace" is displayed on the multi-information display.
|
|