- Short in CAN main bus wire
- Short in CAN branch wire
- Central gateway ECU (network gateway ECU)
- Forward recognition camera
- Millimeter wave radar sensor assembly
- Blind spot monitor sensor LH*2
- Parking assist ECU*3
- Television camera assembly*3, *5
- Clearance warning ECU assembly*4
- Inner rear view mirror assembly*1
- No. 2 CAN junction connector
- No. 8 CAN junction connector
- No. 1 CAN junction terminal
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000021IS8 |
| Model Year Start: 2022 | Model: RAV4 HV | Prod Date Range: [12/2021 - 10/2022] |
| Title: NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): Check Bus 1 Lines for Short Circuit; 2022 MY RAV4 HV [12/2021 - 10/2022] | ||
|
Check Bus 1 Lines for Short Circuit |
DESCRIPTION
There may be a short circuit between the CAN main bus wire and/or CAN branch wire when the resistance between terminals 23 (CA1H) and 8 (CA1L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
|
Symptom |
Trouble Area |
|---|---|
|
*1: w/ Garage Door Opener System (for Digital Inner Mirror Type)
*2: w/ Blind Spot Monitor System *3: w/ Panoramic View Monitor System *4: w/ Intuitive Parking Assist System *5: w/ Parking Assist Monitor System |
|
|
Resistance between terminals 23 (CA1H) and 8 (CA1L) of central gateway ECU (network gateway ECU) is below 54 Ω. |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
-
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Click here
![2019 - 2024 MY RAV4 HV [02/2019 - ]; NETWORKING: CAN COMMUNICATION SYSTEM (for HV Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
- Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) auxiliary battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
-
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
-
Some parts must be initialized and set when replacing or removing and installing parts.
Click here
-
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
-
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click here
HINT:
- Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
- When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
PROCEDURE
|
1. |
CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) auxiliary battery terminal.
(b) Disconnect the No. 2 CAN junction connector.
|
*a |
Front view of wire harness connector (to No. 2 CAN Junction Connector) |
*b |
to Millimeter Wave Radar Sensor Assembly |
|
*c |
to No. 8 CAN Junction Connector |
*d |
to Parking Assist ECU (w/ Panoramic View Monitor System) |
|
*e |
to Forward Recognition Camera |
*f |
to Clearance Warning ECU Assembly (w/ Intuitive Parking Assist System) |
|
*g |
to Central Gateway ECU (Network Gateway ECU) |
*h |
to Inner Rear View Mirror Assembly (w/ Garage Door Opener System (for Digital Inner Mirror Type)) |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
Connected to |
|---|---|---|---|
|
*1: w/ Garage Door Opener System (for Digital Inner Mirror Type)
*2: w/ Intuitive Parking Assist System *3: w/ Panoramic View Monitor System |
|||
|
G102-2 (CANH) - G102-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Millimeter wave radar sensor assembly |
|
G102-3 (CANH) - G102-13 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
No. 8 CAN junction connector |
|
G102-5 (CANH) - G102-15 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Parking assist ECU*3 |
|
G102-6 (CANH) - G102-16 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Forward recognition camera |
|
G102-7 (CANH) - G102-17 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Clearance warning ECU assembly*2 |
|
G102-8 (CANH) - G102-18 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
Central gateway ECU (network gateway ECU) |
|
G102-10 (CANH) - G102-20 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Inner rear view mirror assembly*1 |
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (Central gateway ECU [network gateway ECU] CAN main wire) |
B |
|
NG (No. 8 CAN junction connector CAN main wire) |
C |
|
NG (Wire to ECU or sensor) |
D |
| A |
|
REPLACE NO. 2 CAN JUNCTION CONNECTOR |
| C |
|
| D |
|
|
|
2. |
CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR) |
(a) Reconnect the G102 No. 2 CAN junction connector.
|
(b) Disconnect the central gateway ECU (network gateway ECU) connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G72-23 (CA1H) - G72-8 (CA1L) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
| OK |
|
| NG |
|
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 2 CAN JUNCTION CONNECTOR) |
|
3. |
CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 CAN JUNCTION CONNECTOR) |
(a) Reconnect the G102 No. 2 CAN junction connector.
(b) Disconnect the No. 8 CAN junction connector.
|
*a |
Front view of wire harness connector (to No. 8 CAN Junction Connector) |
*b |
to No. 2 CAN Junction Connector |
|
*c |
to Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System) |
*d |
to Television Camera Assembly (w/ Panoramic View Monitor System, w/ Parking Assist Monitor System) |
|
*e |
to No. 1 CAN Junction Terminal |
- |
- |
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
Connected to |
|---|---|---|---|
|
*1: w/ Blind Spot Monitor System
*2: w/ Panoramic View Monitor System *3: w/ Parking Assist Monitor System |
|||
|
N75-1 (CANH) - N75-12 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
No. 2 CAN junction connector |
|
N75-2 (CANH) - N75-13 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Blind spot monitor sensor LH*1 |
|
N75-3 (CANH) - N75-14 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
200 Ω or higher |
Television camera assembly*2, *3 |
|
N75-4 (CANH) - N75-15 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
No. 1 CAN junction terminal |
|
Result |
Proceed to |
|---|---|
|
OK |
A |
|
NG (No. 1 CAN junction terminal CAN main wire) |
B |
|
NG (No. 2 CAN junction connector CAN main wire) |
C |
|
NG (Wire to ECU or sensor) |
D |
| A |
|
REPLACE NO. 8 CAN JUNCTION CONNECTOR |
| C |
|
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR) |
| D |
|
|
|
4. |
CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR) |
(a) Reconnect the N75 No. 8 CAN junction connector.
|
(b) Disconnect the No. 1 CAN junction terminal connector. |
|
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
N54-3 (CANH) - N54-2 (CANL) |
Cable disconnected from negative (-) auxiliary battery terminal |
108 to 132 Ω |
| OK |
|
REPLACE NO. 1 CAN JUNCTION TERMINAL |
| NG |
|
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION TERMINAL - NO. 8 CAN JUNCTION CONNECTOR) |
|
5. |
CHECK FOR SHORT IN CAN BUS WIRES (ECU, SENSOR) |
(a) Reconnect all wire harness connectors.
(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click here
|
(c) Measure the resistance according to the value(s) in the table below. Standard Resistance:
HINT:
|
|
| OK |
|
REPLACE ECU OR SENSOR |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|