BRAKE SYSTEM (OTHER): BRAKE BOOSTER (w/ Vacuum Brake Booster): REMOVAL; 2022 MY RAV4 RAV4 HV [12/2021

Last Modified: 05-08-2025	6.11:8.1.0	Doc ID: RM1000000021J4O
Model Year Start: 2022	Model: RAV4	Prod Date Range: [12/2021 - 10/2022]
Title: BRAKE SYSTEM (OTHER): BRAKE BOOSTER (w/ Vacuum Brake Booster): REMOVAL; 2022 MY RAV4 RAV4 HV [12/2021 - 10/2022]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during brake booster assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedures	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Battery terminal is disconnected/reconnected	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system
	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for Gasoline model)*
		Pre-collision system
	Memorize steering angle neutral point	Parking assist monitor system
	Memorize steering angle neutral point	Panoramic view monitor system (for Gasoline model)
	Reset back door close position	Power back door system (for Gasoline model)
	Back door lock initialization	Power door lock control system

NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Make sure to release vacuum from the brake booster assembly before removing the brake master cylinder sub-assembly from the brake booster assembly.

Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal

System Name	See Procedure
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system	6 minutes
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system	1 minute

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE BRAKE MASTER CYLINDER SUB-ASSEMBLY

Click here

3. REMOVE ECM

Click here

4. REMOVE BATTERY CLAMP SUB-ASSEMBLY

Click here

5. REMOVE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

6. REMOVE NO. 1 AIR DUCT (for TMC Made)

Click here

7. REMOVE NO. 2 AIR DUCT SUB-ASSEMBLY (for TMMC Made)

Click here

8. REMOVE STOP LIGHT SWITCH ASSEMBLY

Click here

9. REMOVE BRAKE PEDAL RETURN SPRING

Click here

10. SEPARATE WIRE HARNESS

(a) Disconnect the connector.

(b) Disengage the 2 clamps to separate the wire harness from the brake pedal support assembly.

11. LOOSEN LOCK NUT

(a) Loosen the lock nut of the brake master cylinder push rod clevis.

*1	Lock Nut
*2	Brake Master Cylinder Push Rod Clevis

12. REMOVE PUSH ROD PIN

Click here

13. DISCONNECT CHECK VALVE TO CONNECTOR TUBE HOSE

(a) Slide the clip and disconnect the check valve to connector tube hose from the brake booster assembly.

14. REMOVE BRAKE BOOSTER ASSEMBLY

(a) Remove the bolt and nut.

(b) Disengage the guide and separate the wire harness.

Protective Tape

(d) Disconnect the connector from the vacuum warning switch assembly.

(e) w/ Stop and Start System:

(1) Disconnect the connector from the vacuum sensor assembly.

(f) Disengage the 5 clamps to separate the brake tube clamp from the brake lines.

(g) Disengage the 5 clamps to remove the brake tube clamp from the brake lines.

(h) Disengage the 5 clamps to remove the brake tube clamp from the brake lines.

(i) Disengage the 3 clamps to separate the brake tube clamp from the brake lines.

(j) Remove the bolt and clamp to remove the 2 brake tube clamps from the vehicle body.

(k) Using a union nut wrench, remove the 2 brake lines from the brake actuator assembly.

NOTICE:

Do not kink or damage the brake lines.
Do not allow any foreign matter such as dirt or dust to enter the brake lines from the connecting parts.

*a	From 1st Chamber of Brake Master Cylinder Sub-assembly
*b	From 2nd Chamber of Brake Master Cylinder Sub-assembly

(l) Remove the 4 nuts.

NOTICE:

Do not apply excessive force to the brake lines.

(m) Remove the brake master cylinder push rod clevis and lock nut from the brake booster assembly.

(n) Remove the brake booster assembly from the vehicle body.

NOTICE:

Do not apply excessive force to the brake lines.

15. REMOVE BRAKE BOOSTER GASKET

(a) Remove the brake booster gasket from the brake booster assembly.