INSTALLATION

PROCEDURE

1. INSTALL INSTRUMENT PANEL SAFETY PAD ASSEMBLY

(a) Push in the direction indicated by the arrow shown in the illustration and insert the guide to set the instrument panel safety pad assembly.

Install in this Direction

-

-

(b) Install the instrument panel safety pad assembly with the 5 bolts <B>, nut <E> and 2 clips <D>.

(c) Attach the clamp.

	Bolt <B>		Nut <E>
	Clip <D>	-	-

(d) for Automatic Air Conditioning System: Attach the claw to install the cooler (room temp. sensor) thermistor.

(e) Install the steering column assembly with 2 nuts for the instrument panel reinforcement assembly. Torque: 36 N·m {367 kgf·cm, 27 ft·lbf}

(f) w/ Interior Illumination: Connect the connector.

(g) Connect each connector.

*A w/ Navigation System *B w/ Navigation System or Telematics Transceiver

(h) Install the 2 bolts <C>.

Bolt <C>

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(i) Connect the connector and attach the guide.

(j) Connect the airbag connector.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

*A	for Dual Type	*B	for Single Type
	Slide in this Direction	-	-

2. INSTALL HAZARD WARNING SIGNAL SWITCH ASSEMBLY

Click here

3. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

Click here

4. INSTALL NO. 2 SPEAKER HOLE COVER

(a) Insert the guide in direction indicated by the arrow shown in the illustration.

Install in this Direction

(b) Attach the clip to install the No. 2 speaker hole cover as shown in the illustration.

Install in this Direction

5. INSTALL FRONT PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.

Click here

6. INSTALL INSTRUMENT SIDE PANEL RH

(a) Attach the guide as shown in the illustration.

Install in this Direction

(b) Attach the clip to install the instrument side panel RH as shown in the illustration.

Install in this Direction

7. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Attach the clip to install the No. 2 instrument cluster finish panel garnish as shown in the illustration.

Install in this Direction

8. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

(a) Attach the clip to install the lower No. 2 instrument panel finish panel as shown in the illustration.

Install in this Direction

(b) Install the 3 screws <A> and 2 bolts <B>.

	Bolt <B>
	Screw <A>

9. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY

(a) With the glove compartment door assembly in the assembly position, attach the hinge horizontally.

*a	Assembly Position
*b	Closed Position
	Install in this Direction

NOTICE:

Attach the hinges from the top will deform the hinges. Be sure to install the glove compartment door assembly horizontally.

(b) Slightly bend the stoppers (A) and (B) in the directions indicated by the arrows in the illustration and attach the stoppers to install the glove compartment door assembly.

*1	Glove Compartment Door Stopper Sub-assembly
*a	Stopper
	Install in this Direction

(c) Attach the claw to install the glove compartment door stopper sub-assembly.

10. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

(a) w/ Foot light:

Attach the clamp and connect the connector.

HINT:

Even if there is no foot light, if there is a connector, connect the connector and attach the clamp.

(b) Insert the guide in the direction indicated by the arrow shown in the illustration.

Install in this Direction

(c) Lift up in the installation direction, attach the claw in the order shown in the illustration to install the No. 2 instrument panel under cover sub-assembly.

Install in this Direction

11. INSTALL COWL SIDE TRIM BOARD RH

(a) Attach the clamp and clip to install the cowl side trim board RH in the direction indicated by the arrow shown in the illustration.

Install in this Direction

(b) Install the cap nut.

12. INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.

Click here

13. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

(a) Install the front door opening trim weatherstrip RH.

14. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

Click here

15. INSTALL NO. 1 SPEAKER HOLE COVER

(a) Insert the guide in direction indicated by the arrow shown in the illustration.

Install in this Direction

(b) Attach the clip to install the No. 1 speaker hole cover as shown in the illustration.

Install in this Direction

16. INSTALL FRONT PILLAR GARNISH LH

Click here

17. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here

18. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

(a) w/ Smart Key System:

Connect the connector.

(b) Attach the clip to install the lower instrument panel finish panel assembly as shown in the illustration.

Install in this Direction

19. INSTALL FUSE BOX OPENING COVER

(a) for HV Model:

Connect the connector.

(b) Attach the clamp.

*A for 6 Switch Type *B for 3 Switch Type *C for 7 Switch Type

(c) Connect each connector.

(d) Attach the clip to install the fuse box opening cover as shown in the illustration.

Install in this Direction

Bolt <B> or <F>

(e) Install the bolt <B> or <F>.

20. INSTALL FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY (for Gasoline Model)

(a) Attach the guide and claw to install the fuel lid lock open lever sub-assembly in the direction indicated by the arrow as shown in the illustration.

Install in this Direction

21. INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

(a) Attach the guide and claw to install the hood lock control lever sub-assembly in the direction indicated by the arrow shown in the illustration.

Install in this direction

22. INSTALL INSTRUMENT SIDE PANEL LH

(a) Attach the guide as shown in the illustration.

Install in this Direction

(b) Attach the clip to install the instrument side panel LH as shown in the illustration.

Install in this Direction

23. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH

(a) Install the front door opening trim weatherstrip LH.

24. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

(a) w/ Foot light: (1) Attach the claw to install the DLC3. (2) Attach the clamp and connect the connector.

(b) w/o Foot Light:

(1) Attach the claw to install the DLC3. HINT: Even if there is no foot light, if there is a connector, connect the connector and attach the clamp.

(c) Insert the guide in the direction indicated by the arrow shown in the illustration.

Install in this Direction

(d) Lift up in the direction indicated by the arrow shown in the illustration to attach the guide and claw to install the No. 1 instrument panel under cover sub-assembly.

Install in this Direction

(e) Install the 3 screws <A>.

Screw <A>

25. INSTALL COWL SIDE TRIM BOARD LH

(a) Attach the guide and clip to install the cowl side trim board LH in the direction indicated by the arrow shown in the illustration.

Install in this Direction

(b) Install the cap nut.

26. INSTALL FRONT DOOR SCUFF PLATE LH

Click here

27. INSTALL LOWER CENTER INSTRUMENT PANEL FINISH PANEL

(a) Connect each connector.

(b) Attach the clip to install the lower center instrument panel finish panel.

Install in this Direction

28. INSTALL AIR CONDITIONING CONTROL ASSEMBLY

Click here

29. INSTALL COMBINATION METER ASSEMBLY

Click here

30. INSTALL INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY

(a) for 7 Inch Display:

(1) Attach the clip to install the instrument cluster finish panel assembly.

Install in this Direction

(2) Attach the claw and guide.

Install in this Direction

(b) for 12.3 Inch Display:

(1) Attach the clip to install the instrument cluster finish panel assembly.

Install in this Direction

(2) Attach the claw and guide.

Install in this Direction

31. INSTALL INSTRUMENT CLUSTER FINISH PANEL GARNISH

(a) Attach the guide and clip to install the instrument cluster finish panel garnish as shown in the illustration.

Install in this Direction

32. INSTALL RADIO AND DISPLAY RECEIVER ASSEMBLY WITH BRACKET

Click here

33. INSTALL CENTER UPPER INSTRUMENT CLUSTER FINISH PANEL

(a) for 8 Inch Display:

(1) Attach the clip to install the center upper instrument cluster finish panel.

Install in this Direction

(b) for 10.5 Inch Display:

(1) Attach the clip to install the center upper instrument cluster finish panel.

Install in this Direction

34. INSTALL CONSOLE BOX ASSEMBLY

Click here

35. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

36. INSTALL BATTERY HOLE COVER (for HV Model)

Click here

37. INSTALL REAR NO. 2 FLOOR BOARD (for HV Model)

Click here

38. INSTALL DECK BOARD ASSEMBLY (for HV Model)

Click here

39. INSTALL LOWER STEERING COLUMN COVER

Click here

40. CHECK SRS WARNING LIGHT

Click here

41. PERFORM DIAGNOSTIC SYSTEM CHECK

Click here