- Power window regulator motor assembly LH
- Power window regulator motor assembly RH
- Front door window regulator sub-assembly LH
- Front door window regulator sub-assembly RH
- Front door glass sub-assembly LH
- Front door glass sub-assembly RH
- Front door glass run LH
- Front door glass run RH
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM10000000258CM |
| Model Year Start: 2023 | Model: RAV4 | Prod Date Range: [10/2022 - 10/2023] |
| Title: DOOR LOCK: FRONT DOOR LOCK: REMOVAL; 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the front door lock assembly removal/installation are shown below.
Necessary Procedure After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Removal and installation of auxiliary battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system (for HV model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
|
Initialize power window control system |
|
|
NOTICE:
- After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
- When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
Necessary Procedure After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedures |
Necessary Procedures |
Effect/Inoperative Function When Necessary Procedures are not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Removal and installation of auxiliary battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)* |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system (for Gasoline model) |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Initialize power window control system |
|
|
NOTICE:
- After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
- When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure below is for the LH side.
- When removing the front door glass sub-assembly LH, move the front door glass sub-assembly LH to the lowest position before disconnecting the negative (-) auxiliary battery terminal.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2021 - 2024 MY RAV4 RAV4 HV [08/2020 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.
Click here
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
(a) for A25A-FXS:
Click here
(b) for A25A-FKS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH
Click here
7. REMOVE FRONT DOOR ASSIST GRIP COVER LH
Click here
8. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)
Click here
9. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)
Click here
10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Click here
11. REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Click here
12. REMOVE FRONT DOOR REAR BELT SEAL LH
Click here
13. REMOVE FRONT DOOR FRONT BELT SEAL LH
Click here
14. REMOVE FRONT DOOR SERVICE HOLE COVER LH
Click here
15. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Click here
16. REMOVE DOOR FRAME GARNISH LH
Click here
17. REMOVE FRONT DOOR GLASS RUN LH
Click here
18. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
Click here
19. REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Click here
20. REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH (for Driver Side)
Click here
21. REMOVE FRONT DOOR LOCK CYLINDER ASSEMBLY LH (for Driver Side)
Click here
22. REMOVE FRONT DOOR LOCK OPEN ROD LH
(a) Detach the snap as shown in the illustration.
|
*1 |
Snap |
|
Remove in this Direction (1) |
|
Remove in this Direction (2) |
|
Remove in this Direction (3) |
(b) Remove the front door lock open rod LH in the direction indicated by the arrow show in the illustration.
23. REMOVE FRONT DOOR LOCK WITH MOTOR ASSEMBLY LH
|
(a) Using a T30 "TORX" socket wrench, remove the 3 "TORX" screws and front door lock with motor assembly LH. |
|
24. REMOVE DOOR LOCK WIRING HARNESS SEAL
|
(a) When reusing front door lock with motor assembly LH: (1) Remove the door lock wiring harness seal from the front door lock with motor assembly LH. |
|
25. REMOVE FRONT DOOR LOCK COVER SUB-ASSEMBLY LH
(a) Using a screwdriver with its tip wrapped with protective tape, detach the claw and open the front door lock cover sub-assembly LH.
|
|
Remove in this Direction |
|
Protective Tape |
|
(b) Detach the claw and remove the front door lock cover sub-assembly LH. |
|
26. REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY
(a) Detach the clamp and remove the front door lock remote control cable assembly as shown in the illustration.
|
|
Remove in this Direction |
27. REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY
(a) Detach the clamp and remove the front door inside locking cable assembly as shown in the illustration.
|
|
Remove in this Direction |
|
|