- When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle speed is 0 km/h (0 mph), there is no effect on vehicle behavior.
- When the signal sent via either direct line or CAN communication is malfunctioning and indicates that the vehicle is moving, the power switch cannot be turned from on (IG) to off.
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000026KC9 |
| Model Year Start: 2023 | Model: RAV4 HV | Prod Date Range: [10/2022 - ] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): B2282,B2283; Vehicle Speed Signal Malfunction; 2023 - 2024 MY RAV4 HV [10/2022 - ] | ||
|
DTC |
B2282 |
Vehicle Speed Signal Malfunction |
|
DTC |
B2283 |
Vehicle Speed Sensor Malfunction |
DESCRIPTION
DTC B2282 is stored when the vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match.
DTC B2283 is stored when a malfunction in the vehicle speed sensor is detected.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
Note |
|---|---|---|---|---|
|
B2282 |
Vehicle Speed Signal Malfunction |
The vehicle speed signal sent by the combination meter assembly via direct line and the vehicle speed signal sent via CAN communication do not match. (1-trip detection logic*) |
|
DTC Output Confirmation Operation:
|
|
B2283 |
Vehicle Speed Sensor Malfunction |
Vehicle speed signal malfunction is detected (excessive deceleration is detected). (1-trip detection logic*) |
|
DTC Output Confirmation Operation:
|
- *: Only detected while a malfunction is present.
Vehicle Condition and Fail-safe Function when Malfunction Detected
|
DTC Code |
Vehicle Condition when Malfunction Detected |
Fail-safe Function when Malfunction Detected |
|---|---|---|
|
B2282 |
|
- |
|
B2283 |
|
- |
Related Data List and Active Test Items
|
DTC No. |
Data List and Active Test |
|---|---|
|
B2282 B2283 |
Power Source Control
Combination Meter
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart key system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Start Function) after confirming that the communication systems are functioning properly.
Click here
![2022 - 2023 MY RAV4 HV [12/2021 - 10/2023]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
Before replacing the certification ECU (smart key ECU assembly), refer to the Registration.
Click here
- After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (VEHICLE SPEED METER) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Data List.
(e) Read the Data List according to the display on the Techstream.
Body Electrical > Combination Meter > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Vehicle Speed Meter |
Vehicle speed |
Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph) |
Almost same as actual vehicle speed |
- |
Body Electrical > Combination Meter > Data List
|
Tester Display |
|---|
|
Vehicle Speed Meter |
HINT:
Using a speedometer tester, check the actual vehicle speed and the vehicle speed displayed on the Techstream.
OK:
Vehicle speed displayed on the Techstream is almost the same as the actual vehicle speed measured using a speedometer tester.
| NG |
|
|
|
2. |
READ VALUE USING TECHSTREAM (VEHICLE SPEED SIGNAL) |
(a) Enter the following menus: Body Electrical / Power Source Control / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Power Source Control > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Vehicle Speed Signal |
Vehicle being driven or stopped |
Stop or Run |
Stop: Vehicle stopped Run: Vehicle being driven at 5 km/h (3 mph) or more |
- |
Body Electrical > Power Source Control > Data List
|
Tester Display |
|---|
|
Vehicle Speed Signal |
OK:
The Techstream display changes correctly in response to the vehicle condition.
| OK |
|
GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
|
|
3. |
CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - COMBINATION METER ASSEMBLY) |
- *1: except 12.3 Inch Multi-information Display
- *2: for 12.3 Inch Multi-information Display
(a) Disconnect the G54 certification ECU (smart key ECU assembly) connector.
(b) Disconnect the G18*1 or G141*2 combination meter assembly connector.
(c) for Radio and Display Receiver:
Disconnect the G3 radio and display receiver assembly connector.
(d) w/ Navigation System:
Disconnect the H7 navigation ECU connector.
(e) for 9 Speakers:
Disconnect the M3 stereo component amplifier assembly connector.
(f) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
G18-36 (+S) - G54-19 (SPD)*1 |
Always |
Below 1 Ω |
|
G141-8 (+S) - G54-19 (SPD)*2 |
Always |
Below 1 Ω |
|
G18-36 (+S) or G54-19 (SPD) - Other terminals and body ground*1 |
Always |
10 kΩ or higher |
|
G141-8(+S) or G54-19 (SPD) - Other terminals and body ground*2 |
Always |
10 kΩ or higher |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
(a) Reconnect the G54 certification ECU (smart key ECU assembly) connector.
(b) Reconnect the G18*1 or G141*2 combination meter assembly connector.
- *1: except 12.3 Inch Multi-information Display
- *2: for 12.3 Inch Multi-information Display
(c) Using an oscilloscope, check the waveform.
|
*a |
Component with harness connected (Certification ECU (Smart Key ECU Assembly)) |
*b |
Waveform |
OK:
|
Tester Connection |
Condition |
Tool Setting |
Specified Condition |
|---|---|---|---|
|
G54-19 (SPD) - G54-18 (E) |
Vehicle being driven at approximately 5 km/h (3 mph) |
5 V/DIV., 20 ms./DIV. |
Pulse generation (See waveform) |
HINT:
The wavelength becomes shorter as the vehicle speed increases.
| OK |
|
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
|
| NG |
|
|
|