Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026LJQ |
Model Year Start: 2023 |
Model: RAV4 |
Prod Date Range: [10/2022 - 10/2023] |
Title: A25A-FKS (ENGINE CONTROL): ECM: REMOVAL; 2023 MY RAV4 [10/2022 - 10/2023] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during ECM removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Battery terminal is disconnected/reconnected
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system (for Gasoline model)*
|
Pre-collision system
|
Reset back door close position
|
Power back door system (for Gasoline model)
|
|
Back door lock initialization
|
Power door lock control system
|
|
ECM
|
Perform Vehicle Identification Number (VIN) or frame number registration
|
DTC P063051 is output
|
|
Code registration
|
Engine start function
|
w/ Smart Key System:
w/o Smart Key System:
|
for UB80E:
-
If transaxle compensation code read from ECM
-
Perform reset memory
-
Transfer transaxle compensation code
-
Perform road test to allow ECM to learn
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
for Initialization:
for Registration:
|
for UB80E:
-
If transaxle compensation code not read from ECM
-
Perform reset memory
-
Reset transaxle compensation code
-
Perform road test to allow ECM to learn
|
for UB80F:
-
If transaxle compensation code read from ECM
-
Perform reset memory
-
Transfer transaxle compensation code
-
Perform road test to allow ECM to learn
|
-
Large shift shock
-
Deterioration of fuel efficiency
|
for Initialization:
for Registration:
|
for UB80F:
-
If transaxle compensation code not read from ECM
-
Perform reset memory
-
Reset transaxle compensation code
-
Perform road test to allow ECM to learn
|
NOTICE:
-
If the ECM has been struck or dropped, replace it.
-
Perform Vehicle Identification Number (VIN) registration when replacing the ECM.
Click here
-
After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, be sure to wait for the time specified in the following table before disconnecting the cable from the negative (-) battery terminal.
Waiting Time before Disconnecting Cable from Negative (-) Battery Terminal
System Name
|
See Procedure
|
Vehicle enrolled in Toyota Audio Multimedia system or safety connect system
|
6 minutes
|
Vehicle not enrolled in Toyota Audio Multimedia system and safety connect system
|
1 minute
|
PROCEDURE
1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Click here
2. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY
Click here
3. REMOVE INLET AIR CLEANER ASSEMBLY
Click here
4. REMOVE AIR CLEANER ASSEMBLY WITH AIR CLEANER HOSE
Click here
5. REMOVE ECM
(a) Rotate the 3 levers while pushing the locks, and disconnect the 3 ECM connectors.
NOTICE:
After disconnecting the ECM connectors, make sure that dirt, water or other foreign matter does not contact the connecting parts of the ECM connectors.
|
|
(b) Remove the 2 bolts, nut and ECM.
NOTICE:
If the ECM has been struck or dropped, replace it.
|
|
6. REMOVE NO. 1 ECM BRACKET
(a) Remove the 2 screws and No. 1 ECM bracket from the ECM.
|
|
7. REMOVE NO. 2 ECM BRACKET
(a) Remove the 2 screws and No. 2 ECM bracket from the ECM.
|
|
|