AXLE AND DIFFERENTIAL: FRONT AXLE HUB: REMOVAL; 2023 MY RAV4 RAV4 HV [10/2022

Last Modified: 05-08-2025	6.11:8.1.0	Doc ID: RM1000000026QFV
Model Year Start: 2023	Model: RAV4	Prod Date Range: [10/2022 - 10/2023]
Title: AXLE AND DIFFERENTIAL: FRONT AXLE HUB: REMOVAL; 2023 MY RAV4 RAV4 HV [10/2022 - 10/2023]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front axle hub assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model:)

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for HV model)*
		Pre-collision system
	Reset back door close position	Power back door system (for HV model)
	Back door lock initialization	Power door lock control system
Front wheel alignment adjustment	Perform "Reset Memory" Perform "Calibration"	DTCs are stored ABS warning light illuminates Brake system warning light (yellow indicator) illuminates Slip indicator light illuminates Brake control disabled or malfunctions (brake drag, etc.)

NOTICE:

After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model:)

Replaced Part or Performed Procedure	Necessary Procedure	Effect/Inoperative Function When Necessary Procedures are not Performed	Link
Front wheel alignment adjustment	Perform "Reset Memory". Perform acceleration sensor zero point calibration and store system information memorization.	VSC is disabled or malfunctions DTCs are output Slip indicator light illuminates ABS warning light illuminates

HINT:

Use the same procedure for the RH and LH sides.
The following procedure is for the LH side.

PROCEDURE

1. DISABLE BRAKE CONTROL (w/o Vacuum Brake Booster)

Click here

2. REMOVE FRONT WHEEL

Click here

3. REMOVE FRONT AXLE SHAFT NUT LH

(a) Using SST and a hammer, unstake the staked part of the front axle shaft nut.

SST: 09930-00010

09931-00010

09931-00020

NOTICE:

Loosen the staked part of the front axle shaft nut completely, otherwise the screw of the drive shaft may be damaged.

(b) While applying the brakes, remove the front axle shaft nut.

4. DISCONNECT FRONT SPEED SENSOR LH

(a) Remove the bolt and disconnect the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.

(b) Remove the bolt, disengage the clamp and disconnect the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:

Prevent foreign matter from contacting the sensor tip.
Be careful not to damage the front speed sensor.
Clean the speed sensor installation hole and the contact surfaces every time the front speed sensor is removed.

5. DISCONNECT TIE ROD ASSEMBLY LH

Click here

6. DISCONNECT FRONT DISC BRAKE CALIPER ASSEMBLY LH

Click here

7. REMOVE FRONT DISC

Click here

8. DISCONNECT FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH

(a) Remove the bolt and 2 nuts and disconnect the front lower No. 1 suspension arm sub-assembly from the front lower ball joint assembly.

9. DISCONNECT FRONT DRIVE SHAFT ASSEMBLY LH

(a) Place matchmarks on the front axle hub LH and front drive shaft assembly LH as shown in the illustration.

Matchmark

(b) Using a plastic hammer, disconnect the front drive shaft assembly from the front axle assembly.

NOTICE:

Do not damage the front drive shaft outboard joint boot.
Do not push the front axle assembly towards the outside of the vehicle any further than necessary.

HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.

10. REMOVE FRONT AXLE ASSEMBLY LH

(a) Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.

11. REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

(a) Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.

(b) Remove the 4 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:

Do not drop the front axle hub sub-assembly.
Be careful not to damage the speed sensor rotor or contact surfaces.
Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.