| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM1000000026SZV |
| Model Year Start: 2023 | Model: RAV4 HV | Prod Date Range: [10/2022 - ] |
| Title: PARK ASSIST / MONITORING: PANORAMIC VIEW MONITOR SYSTEM (for HV Model): HOW TO PROCEED WITH TROUBLESHOOTING; 2023 - 2024 MY RAV4 HV [10/2022 - ] | ||
|
HOW TO PROCEED WITH TROUBLESHOOTING |
CAUTION / NOTICE / HINT
HINT:
- Use the following procedure to troubleshoot the panoramic view monitor system.
- *: Use the GTS.
PROCEDURE
|
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
|
2. |
CUSTOMER PROBLEM ANALYSIS |
(a) Ask the customer about the problems and the conditions at the time the malfunction occurred to make sure the problem symptom was not temporarily caused by radio waves in the surrounding environment.
HINT:
The panoramic view monitor display may be temporarily distorted due to radio waves around the vehicle.
|
Problem Symptom |
Cause |
|---|---|
|
The problem symptom indicates a panoramic view monitor display malfunction and the problem symptom cannot be reproduced. |
The display may be temporarily distorted when the vehicle is close to an object that transmits radio waves, such as a telecommunication tower, an airport or a truck equipped with a transceiver. |
|
|
3. |
INSPECT AUXILIARY BATTERY VOLTAGE |
(a) Measure the auxiliary battery voltage with the ignition switch off.
Standard voltage:
11 to 14 V
If the voltage is below 11 V, replace or recharge the auxiliary battery before proceeding.
|
|
4. |
CHECK AUDIO AND VISUAL SYSTEM |
(a) Refer to the audio and visual system.
Click here
![2023 - 2024 MY RAV4 RAV4 HV [10/2022 - ]; AUDIO / VIDEO: AUDIO AND VISUAL SYSTEM: PROBLEM SYMPTOMS TABLE](/t3Portal/stylegraphics/info.gif)
|
Result |
Proceed to |
|---|---|
|
Audio and visual system and navigation system is normal. |
A |
|
Audio and visual system is abnormal |
B |
| B |
|
|
|
5. |
CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Use the GTS to check if the CAN communication system is functioning normally.
Click here
|
Result |
Proceed to |
|---|---|
|
CAN DTCs are not output |
A |
|
CAN DTCs are output |
B |
| B |
|
|
|
6. |
CHECK FOR DTC* |
(a) Check for DTCs and note any codes that are output.
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
(b) Clear the DTCs.
Chassis > Circumference Monitoring Camera Control Module > Clear DTCs
(c) Recheck for DTCs. Try to reproduce the problem symptoms based on the recorded DTCs, and then check if the DTCs are output again.
Chassis > Circumference Monitoring Camera Control Module > Trouble Codes
|
Result |
Proceed to |
|---|---|
|
DTC is not output |
A |
|
DTC is output |
B |
| B |
|
|
|
7. |
CHECK FOR VEHICLE CONTROL HISTORY (RoB)* |
HINT:
Refer to Vehicle Control History (RoB).
Click here
(a) Check for vehicle control history (RoB) and note any codes that are output.
Chassis > Circumference Monitoring Camera Control Module > Utility
|
Tester Display |
|---|
|
Vehicle Control History (RoB) |
|
Result |
Proceed to |
|---|---|
|
No vehicle control history (RoB) is output |
A |
|
Vehicle control history (RoB) is output |
B |
| B |
|
|
|
8. |
PROBLEM SYMPTOMS TABLE |
(a) Refer to the Problem Symptoms Table.
Click here
|
Result |
Proceed to |
|---|---|
|
Fault is not listed in Problem Symptoms Table |
A |
|
Fault is listed in Problem Symptoms Table |
B |
| B |
|
|
|
9. |
OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Data List / Active Test
Click here
(b) Terminals of ECU
Click here
|
|
10. |
ADJUST, REPAIR OR REPLACE |
|
|
11. |
CONFIRMATION TEST |
| NEXT |
|
END |
|
|