Last Modified: 01-30-2024 |
6.11:8.1.0 |
Doc ID: RM1000000026X28 |
Model Year Start: 2023 |
Model: RAV4 |
Prod Date Range: [10/2022 - 10/2023] |
Title: A25A-FKS (FUEL): FUEL PUMP (w/ Canister Pump Module): REMOVAL; 2023 MY RAV4 [10/2022 - 10/2023] |
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure
|
Necessary Procedure
|
Effect/Inoperative Function when Necessary Procedure not Performed
|
Link
|
Battery terminal is disconnected/reconnected
|
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)
|
Stop and start system
|
|
Perform steering sensor zero point calibration
|
Lane control system
|
|
Parking support brake system*
|
Pre-collision system
|
Reset back door close position
|
Power back door system
|
|
Back door lock initialization
|
Power door lock control system
|
|
Replacement of fuel pump
|
Inspection after repair
|
-
Poor idle, etc.
-
Engine start function, etc.
|
|
CAUTION:
-
Never perform work on fuel system components near any possible ignition sources.
-
Vaporized fuel could ignite, resulting in a serious accident.
-
Do not perform work on fuel system components without first disconnecting the cable from the negative (-) battery terminal.
-
Sparks could cause vaporized fuel to ignite, resulting in a serious accident.
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click here
2. DISCHARGE FUEL SYSTEM PRESSURE
Click here
3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
4. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY
Click here
5. REMOVE REAR SEAT CUSHION LOCK HOOK
Click here
6. REMOVE REAR FLOOR SERVICE HOLE COVER (for LH Side)
(a) Remove the rear floor service hole cover and butyl tape.
(b) Disconnect the 2 connectors from the fuel suction with pump and gauge tube assembly.
|
|
7. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
(a) Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.
*1
|
Tube Joint Clip
|
*2
|
Fuel Tank Main Tube Sub-assembly
|
*a
|
Nylon Tube
|
*b
|
Fuel Tube Joint
|
*c
|
Plate Sub-assembly
|
*d
|
O-ring
|
|
Pull off
|
|
Pull off
|
NOTICE:
-
Remove any foreign matter on the fuel tube joint before performing this work.
-
Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).
-
Be sure to disconnect the fuel tube joint by hand.
-
Do not bend, twist, pinch or kink the nylon tube.
-
Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.
-
If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.
8. REMOVE FUEL PUMP GAUGE RETAINER
(a) Detach the claw to remove the No. 1 fuel tube clamp from the fuel pump gauge retainer.
|
|
(b) Remove the fuel pump gauge retainer.
(1) Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.
SST: 09808-14031
09808-01030
09808-01050
SST: 09808-01071
HINT:
Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.
|
|
*a
|
SST (Plate)
|
*b
|
SST (Bolt)
|
*c
|
SST (Claw)
|
*d
|
Insertion Point
|
|
|
(2) While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).
(3) Install SST (handle) to SST (plate).
SST: 09808-14031
09808-01010
SST: 09808-01071
|
|
*a
|
SST (Handle)
|
*b
|
SST (Plate)
|
*c
|
SST (Bolt)
|
*d
|
SST (Claw)
|
|
|
(4) Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.
NOTICE:
-
Do not use any tools other than specified in this operation as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.
-
Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.
-
Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.
-
Do not spin SST too fast or use an impact wrench as this may result in damage to components.
-
If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.
(5) While pressing down on the fuel suction with pump and gauge tube assembly, remove the fuel pump gauge retainer.
9. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
(a) Disconnect the fuel return vent tube sub-assembly and remove the fuel suction with pump and gauge tube assembly from the fuel tank assembly.
Click here
NOTICE:
Be careful not to bend the arm of the fuel sender gauge assembly.
|
|
(b) Remove the gasket from the fuel tank assembly.
|
|
|