- Occupant classification system
- Passenger airbag ON/OFF indicator
- Airbag system (Front passenger side)
- Seat belt warning system (Front passenger)
| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002EKGG |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: SEAT BELT: FRONT SEAT INNER BELT ASSEMBLY (for Manual Seat): REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat inner belt assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here
*2: w/o Power Back Door System |
|||
|
Disconnect cable from negative (-) battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)*1 |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization*2 |
Power door lock control system |
|
|
|
Front passenger seat |
Zero point calibration (Occupant classification system) |
|
|
HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing.
Click here
![2021 - 2024 MY RAV4 RAV4 HV [08/2020 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here
2. REMOVE FRONT SEAT ASSEMBLY LH
Click here
3. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH (for Driver Side)
(a) Detach the clamp and claw.
(b) Disconnect the connector.
|
(c) Remove the nut and front seat inner belt assembly LH. |
|
(d) Remove the front seat belt anchor plate.
4. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH (for Front Passenger Side)
(a) Detach the clamp and disconnect the connector.
|
(b) Remove the nut and front seat inner belt assembly RH. |
|
(c) Remove the front seat belt anchor plate.
|
|