| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002EKGI |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: SEAT BELT: FRONT SEAT OUTER BELT ASSEMBLY: REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 - ] | ||
REMOVAL
CAUTION / NOTICE / HINT
The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during front seat outer belt assembly removal/installation are shown below.
Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*: When performing learning using the Techstream.
Click here
|
|||
|
Disconnect cable from negative (-) battery terminal |
Perform steering sensor zero point calibration |
Lane control system |
|
|
Parking support brake system (for HV model)* |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization |
Power door lock control system |
|
|
Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)
|
Replaced Part or Performed Procedure |
Necessary Procedure |
Effect/Inoperative Function when Necessary Procedure not Performed |
Link |
|---|---|---|---|
|
*1: When performing learning using the Techstream.
Click here
*2: w/o Power Back Door System |
|||
|
Disconnect cable from negative (-) battery terminal |
Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) |
Stop and start system |
|
|
Perform steering sensor zero point calibration |
Lane control system |
|
|
|
Parking support brake system (for Gasoline model)*1 |
|||
|
Pre-collision system |
|||
|
Reset back door close position |
Power back door system |
|
|
|
Back door lock initialization*2 |
Power door lock control system |
|
|
HINT:
- Use the same procedure for the RH and LH sides.
- The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read precaution thoroughly before servicing.
Click here
![2021 - 2024 MY RAV4 RAV4 HV [08/2020 - ]; SUPPLEMENTAL RESTRAINT SYSTEMS: AIRBAG SYSTEM: PRECAUTION](/t3Portal/stylegraphics/info.gif)
NOTICE:
After the ignition switch is turned off, the navigation system requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) auxiliary battery terminal.
Click here
2. REMOVE DECK BOARD ASSEMBLY (for HV Model)
Click here
3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)
Click here
4. REMOVE BATTERY HOLE COVER (for HV Model)
Click here
5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL
-
for A25A-FKS:
Click here
-
for A25A-FXS:
Click here
CAUTION:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
- If the airbag deploys for any reason, it may cause a serious accident.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
6. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY (for Gasoline Model)
Click here
7. REMOVE REAR SEAT CUSHION LOCK HOOK (for Gasoline Model)
Click here
8. REMOVE FRONT DOOR SCUFF PLATE LH
Click here
9. REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Pull back the front door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.
Click here
10. REMOVE REAR DOOR SCUFF PLATE LH
Click here
11. REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
HINT:
Pull back the rear door opening trim weatherstrip LH so that the lower center pillar garnish LH can be removed.
Click here
12. REMOVE LAP BELT OUTER ANCHOR COVER
|
(a) Detach the claw and guide to remove the lap belt outer anchor cover. |
|
13. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH (FLOOR ANCHOR)
|
(a) Remove the bolt and the floor anchor of the front seat outer belt assembly LH. |
|
14. REMOVE LOWER CENTER PILLAR GARNISH LH
Click here
15. REMOVE CENTER PILLAR GARNISH LH
Click here
16. REMOVE FRONT SEAT OUTER BELT ASSEMBLY LH
|
(a) Remove the nut and the shoulder anchor of the front seat outer belt assembly LH. |
|
(b) Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the pretensioner connector as shown in the illustration.
|
*a |
Locking Button |
|
Remove in this Direction |
|
Protective Tape |
HINT:
Tape the thin-bladed screwdriver tip before use.
(c) for Front Passenger Seat Belt with Selectable Force Limiter:
(1) Using a thin-bladed screwdriver, pull out the locking button to release the lock to disconnect the selectable force limiter connector as shown in the illustration.
|
*a |
Locking Button |
|
|
Remove in this Direction |
|
|
Protective Tape |
HINT:
Tape the thin-bladed screwdriver tip before use.
|
(d) Remove the bolt. |
|
(e) Detach the guide to remove the front seat outer belt assembly LH.
17. REMOVE FRONT SHOULDER BELT ANCHOR ADJUSTER ASSEMBLY
HINT:
Perform this procedure when replacing the front shoulder belt anchor adjuster assembly.
|
(a) Remove the 2 bolts. |
|
(b) Detach the guide to remove the front shoulder belt anchor adjuster assembly.
18. REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH
HINT:
Perform this procedure when replacing the front shoulder belt anchor plate sub-assembly LH.
|
(a) Detach the guide to remove the front shoulder belt anchor plate sub-assembly LH. |
|
|
|