SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000002EKHK
Model Year Start: 2024	Model: RAV4	Prod Date Range: [10/2023 - ]
Title: SUPPLEMENTAL RESTRAINT SYSTEMS: SIDE AIRBAG SENSOR (for Front Door): REMOVAL; 2024 MY RAV4 RAV4 HV [10/2023 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during side airbag pressure sensor removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for Gasoline Model)

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed
1: When performing learning using the Techstream. 2: w/o Power Back Door System Click here
Disconnect cable from negative (-) auxiliary battery terminal	Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes)	Stop and start system
	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for Gasoline model)*1
		Pre-collision system
	Reset back door close position	Power back door system (for Gasoline model)
	Back door lock initialization*2	Power door lock control system

NOTICE:

After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)

Replaced Part or Performed Procedures	Necessary Procedures	Effect/Inoperative Function When Necessary Procedures are not Performed
*: When performing learning using the Techstream. Click here
Disconnect cable from negative (-) auxiliary battery terminal	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system (for HV model)*
		Pre-collision system
	Reset back door close position	Power back door system (for HV model)
	Back door lock initialization	Power door lock control system

NOTICE:

After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

HINT:

Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.

PROCEDURE

1. PRECAUTION

CAUTION:

Be sure to read precaution thoroughly before servicing.

Click here

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

Click here

2. REMOVE DECK BOARD ASSEMBLY (for HV Model)

Click here

3. REMOVE REAR NO. 2 FLOOR BOARD (for HV Model)

Click here

4. REMOVE BATTERY HOLE COVER (for HV Model)

Click here

5. DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

for A25A-FKS:
Click here
for A25A-FXS:
Click here

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If the airbag deploys for any reason, it may cause a serious accident.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here

6. REMOVE FRONT DOOR INSIDE HANDLE BEZEL LH

Click here

7. REMOVE FRONT DOOR ASSIST GRIP COVER LH

Click here

8. REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Driver Side)

Click here

9. REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT DOOR ARMREST BASE PANEL (for Front Passenger Side)

Click here

10. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

Click here

11. REMOVE FRONT DOOR SERVICE HOLE COVER LH

Click here

12. REMOVE SIDE AIRBAG PRESSURE SENSOR LH

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) auxiliary battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.
If this procedure is performed without disconnecting the negative (-) auxiliary battery terminal, the airbag may deploy even if an impact is applied only to the side airbag pressure sensor. Therefore, make sure that the negative (-) auxiliary battery terminal is disconnected before performing this procedure.

(d) Detach the claw and pull out the side airbag pressure sensor LH.

NOTICE:

If the side airbag pressure sensor LH has been dropped, replace it with a new one.

(e) Disconnect the airbag connector.

NOTICE:

When disconnecting any airbag connector, take care not to damage the airbag wire harness.

(1) Push down the housing lock and slide the CPA. (At this time, the connector cannot be disconnected yet.)

*a	Housing Lock	*b	CPA
*c	CPA Upper Part	*d	Connector Lock is Released

(2) Push the housing lock again and disconnect the connector.

NOTICE:

Do not push down the upper part of the CPA shown in the illustration when disconnecting the airbag connector.

(3) After disconnecting the connector, check that the position of the housing lock is correct as shown in the illustration.

*a	CPA	*b	Housing
*c	Correct	*d	Incorrect