| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002EMAJ |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: STOP AND START: STOP AND START SYSTEM: Engine Hood Courtesy Switch Circuit; 2024 MY RAV4 [10/2023 - ] | ||
|
Engine Hood Courtesy Switch Circuit |
DESCRIPTION
The engine stop and start ECU detects whether the engine hood is open or closed based on a signal received from the engine hood courtesy switch built into the hood lock assembly.
- The engine stop and start ECU prohibits starting of the engine by stop and start control and changes the mode to "stalled" if the engine hood is opened with the shift lever in D while the engine is stopped by stop and start control.
WIRING DIAGRAM
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM (HOOD COURTESY SWITCH) |
NOTICE:
Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.
Powertrain > Stop and Start > Data List
|
Tester Display |
|---|
|
Hood Courtesy Switch |
(e) According to the display on the Techstream, read the Data List.
OK:
|
Techstream Display |
Condition |
Normal Condition |
|---|---|---|
|
Hood Courtesy Switch |
Engine hood closed |
ON |
|
Engine hood open |
OFF |
| OK |
|
CHECK AND ADJUST HOOD LOCK ASSEMBLY FITTING (ENGINE HOOD COURTESY SWITCH) (ADJUST HOOD) |
|
|
2. |
INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH) |
(a) Inspect the engine hood courtesy switch (hood lock assembly).
Click here
![2019 - 2024 MY RAV4 RAV4 HV [11/2018 - ]; THEFT DETERRENT / KEYLESS ENTRY: ENGINE HOOD COURTESY SWITCH: INSPECTION](/t3Portal/stylegraphics/info.gif)
| NG |
|
|
|
3. |
CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND) |
(a) Disconnect the engine hood courtesy switch (hood lock assembly) connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A17-2 (E) - Body ground |
Always |
Below 1 Ω |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
4. |
CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY)) |
(a) Disconnect the engine stop and start ECU connector.
(b) Disconnect the engine hood courtesy switch (hood lock assembly) connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A34-7 (BNT1) - A17-1 (+) |
Always |
Below 1 Ω |
|
A34-7 (BNT1) or A17-1 (+) - Body ground and other terminals |
Always |
10 kΩ or higher |
| OK |
|
CHECK AND ADJUST HOOD LOCK ASSEMBLY FITTING (ENGINE HOOD COURTESY SWITCH) (ADJUST HOOD) |
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|