Last Modified: 01-30-2024 6.11:8.1.0 Doc ID: RM100000002FQ21
Model Year Start: 2024 Model: RAV4 Prod Date Range: [10/2023 -           ]
Title: DOOR / HATCH: POWER BACK DOOR SYSTEM: DATA LIST / ACTIVE TEST; 2024 MY RAV4 RAV4 HV [10/2023 -        ]

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

(a) According to the display on the GTS, read the Data List.

Body Electrical > Back Door > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Total Distance Traveled

Total distance traveled

0 to 16777215

Same as actual total distance traveled

For the unit, refer to "Total Distance Traveled - Unit"

Total Distance Traveled - Unit

Total Distance Traveled - unit

km or mile

km: km

mile: mile

-

Back Door Lock Status

Back door condition signal

Lock or Unlock

Lock: Back door locked

Unlock: Back door unlocked

-

Half Latch Switch

Latch switch signal

ON or OFF

ON: When in the open latch or overstroke position

OFF: Half latch position → full latch position

-

Closer Position Switch

Initial switch signal

ON or OFF

ON: Back door lock sector gear in center position (Initial switch on)

OFF: Back door lock sector gear out of center position (Initial switch off)

-

Pawl Switch

Pawl switch signal

ON or OFF

ON: Back door lock motor open-latched

OFF: Back door lock motor except open latched

-

Courtesy Switch

Back door courtesy switch signal

ON or OFF

ON: Open latch position → half latch position

OFF: Full latch position → overstroke position

-

PBD Main Switch

Power back door ON/OFF signal

ON or OFF

Current customize setting displayed

-

PBD Close Switch

No. 1 power back door control switch signal

ON or OFF

ON: No. 1 power back door control switch pushed

OFF: No. 1 power back door control switch not pushed

-

IG Switch

Ignition switch signal

ON or OFF

ON: Ignition switch ON

OFF: Ignition switch off

"OFF" is also displayed for this item when the ignition switch to ACC.

Kick Sensor Function

Status of the hands free power back door function*

ON or OFF

ON: Hands free power back door ON

OFF: Hands free power back door off

-

Door Lock Signal

Back door condition signal

Lock or Unlock

Lock: Back door locked

Unlock: Back door unlocked

-

Status of Kick Sensor Detection

Kick door control sensor ON detection status*

ON or OFF

ON: Kick door control sensor ON detected

OFF: Kick door control sensor ON not detected

-

Status of Kick Sensor Abnormal

Kick door control sensor abnormal condition*

Normal or Abnormal

Normal: Kick door control sensor normal

Abnormal: Kick door control sensor abnormal

-

Kick Sensor Installation

Kick door control sensor installed condition*

ON or OFF

ON: Kick door control sensor incorrectly installed

OFF: Kick door control sensor correctly installed

-

PBD Touch Sensor RH

Power back door sensor assembly RH signal

ON, OFF or Open

ON: Power back door sensor assembly RH pressed

OFF: Power back door sensor assembly RH not pressed

Open: Power back door sensor assembly RH circuit open

-

PBD Touch Sensor LH

Power back door sensor assembly LH signal

ON, OFF or Open

ON: Power back door sensor assembly LH pressed

OFF: Power back door sensor assembly LH not pressed

Open: Power back door sensor assembly LH circuit open

-

Correction of Back Door Position

Correction of back door position

Not Complied With or Complied With

Not Complied With: not complied with

Complied With: complied with

-

PBD Close Switch Operation History

Power back door control switch operation history

ON or OFF

ON: Has operation history

OFF: No operation history

The operation history will be cleared by disconnecting the cable from the negative (-) terminal of the auxiliary battery for approximately 30 seconds.

Close & Lock Switch Operation History

Back door control switch operation history

ON or OFF

ON: Has operation history

OFF: No operation history

Although the item is displayed on the GTS, it is not applicable to this vehicle

Kick Sensor Status

Kick Sensor condition signal*

Normal, Sensitivity Low (Noise), Stop (Foreign Objects), Sensitivity Low (Noise) & Stop (Foreign Objects), Stop (Battery Protection), Sensitivity Low (Noise) & Stop (Battery Protection), Stop (Foreign Objects) & Stop (Battery Protection) or Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection)

Normal: Kick sensor detection status normal

Sensitivity Low (Noise): Kick sensor detection sensitivity decreased due to noise

Stop (Foreign Objects): Kick sensor detection stopped due to foreign objects

Sensitivity Low (Noise) & Stop (Foreign Objects): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects

Stop (Battery Protection): Kick sensor detection stopped due to battery protection

Sensitivity Low (Noise) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to battery protection

Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor detection stopped due to foreign objects and battery protection

Sensitivity Low (Noise) & Stop (Foreign Objects) & Stop (Battery Protection): Kick sensor sensitivity decreased due to noise and detection stopped due to foreign objects and battery protection

-

Opened Number of Times

Number of times for back door opened

0 to 214783647

Number of times for back door opened

-

Closed Number of Times

Number of times for back door closed

0 to 214783647

Number of times for back door closed

-

PBD SW Operating Condition Setting

Back door control switch operation

ON or 0.8s

Current customize setting displayed

-

PBD Buzzer Function

Status of the power back door warning buzzer

ON or OFF

Current customize setting displayed

-

PBD Assist Close Function

Function that enables/disables the power back door assist close operation. When set to ON, the back door will close automatically when operated in the close direction manually.

ON or OFF

Current customize setting displayed

-

PBD Assist Open Function

Function that enables/disables the power back door assist open operation. When set to ON, the back door will open automatically when the back door opener switch assembly (open switch) is operated.

ON or OFF

Current customize setting displayed

-

PBD Door Unlock with One Motion Setting

Door or doors to be unlocked when back door locked and power back door operated by pressing transmitter switch (electrical key transmitter sub-assembly).

Back Door or All Doors

Current customize setting displayed

-

PBD Wireless Function

Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly).

ON or OFF

Current customize setting displayed

-

PBD Wireless One Motion Function

Wireless one motion function

ON or OFF

Current customize setting displayed

-

PBD Wireless SW Setting

Wireless operation setting condition

1 Time Press, 2 Times Press or Long Press (0.8s)

Current customize setting displayed

-

PBD Kick Sensor Sensitivity Adjust

Function that changes the sensitivity of the kick sensor.*

Normal, +1, +2 or Unknown

Current customize setting displayed

-

PBD Kick-in Beep Sound

Function that sounds a buzzer when a kick operation detected.*

ON or OFF

Current customize setting displayed

-

  • *: w/ Hands Free Power Back Door

Body Electrical > Main Body > Data List

Tester Display

Measurement Item

Range

Normal Condition

Diagnostic Note

Back Door Courtesy SW

Back door courtesy switch signal

ON or OFF

ON: Back door open

OFF: Back door closed

-

Back Door Open

Back door condition signal

Permit or Prohibit

Permit: Back door unlocked

Prohibit: Back door locked

-

Back Door Open SW

Power back door switch assembly signal

ON or OFF

ON: Power back door switch assembly on

OFF: Power back door switch assembly off

-

Back Door Open Handle SW

Back door opener switch assembly (open switch) signal

ON or OFF

ON: Back door opener switch assembly (open switch) on

OFF: Back door opener switch assembly (open switch) off

-

Kick Sensor Operation with ACC ON

Status of the hands free power back door function with power switch on (ACC)*

Not Available or Available

Current customize setting displayed

-

  • *: w/ Hands Free Power Back Door

ACTIVE TEST

HINT:

Using the GTS, perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) According to the display on GTS perform the "Active Test".

Body Electrical > Back Door > Active Test

Tester Display

Measurement Item

Control Range

Diagnostic Note

PBD Motor (Open)

Power back door motor operation

Start

-

PBD Motor (Close)

Power back door motor operation

Start

-

PBD Buzzer (Small Volume)

Power back door warning buzzer sound (small volume)

Start

-

PBD Buzzer (Middle Volume)

Power back door warning buzzer sound (Middle volume)

Start

-

PBD Buzzer (Large Volume)

Power back door warning buzzer sound (Large volume)

Start

-

PBD Release Closer

Latch release operation

Start

-