| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002FQ2A |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: DOOR / HATCH: POWER BACK DOOR SYSTEM: B225001; Back Door Closer General Electrical Failure; 2024 MY RAV4 RAV4 HV [10/2023 - ] | ||
|
DTC |
B225001 |
Back Door Closer General Electrical Failure |
DESCRIPTION
The back door closer is controlled by the multiplex network door ECU.
The multiplex network door ECU determines the latch position of the back door lock with courtesy light switch assembly based on the combination of signals from the latch switch built into the back door lock with courtesy light switch assembly, back door courtesy switch, sector switch (home position switch) and pawl switch.
This DTC is stored when the back door closer is operating and the sector switch (home position switch) signal indicates that the latch is not in the correct position within the specified amount of time.
When this DTC is output, the multiplex network door ECU suspends back door closer control and power back door control.
|
DTC No. |
Detection Item |
DTC Detection Condition |
Trouble Area |
|---|---|---|---|
|
B225001 |
Back Door Closer General Electrical Failure |
While the back door closer is operating, a malfunction is detected in position information from the initial switch within a specified amount of time. |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
If the multiplex network door ECU has been replaced, or if any of the connectors has been disconnected, initialize the power back door system.
Click here
![2024 MY RAV4 RAV4 HV [10/2023 - ]; DOOR / HATCH: POWER BACK DOOR SYSTEM: INITIALIZATION](/t3Portal/stylegraphics/info.gif)
PROCEDURE
|
1. |
READ VALUE USING GTS |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Back Door > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Closer Position Switch |
Initial switch signal |
ON or OFF |
OFF: Back door lock sector gear out of center position (Initial switch off) |
- |
Body Electrical > Back Door > Data List
|
Tester Display |
|---|
|
Closer Position Switch |
|
Result |
Proceed to |
|---|---|
|
The value of Closer Position Switch is OFF |
A |
|
None of the above conditions are met |
B |
| B |
|
|
|
2. |
READ VALUE USING GTS |
(a) Read the Data List according to the display on the GTS.
Body Electrical > Back Door > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Closer Position Switch |
Initial switch signal |
ON or OFF |
ON: Back door lock sector gear in center position (Initial switch on) |
- |
Body Electrical > Back Door > Data List
|
Tester Display |
|---|
|
Closer Position Switch |
|
Result |
Proceed to |
|---|---|
|
The value of Closer Position Switch is ON |
A |
|
None of the above conditions are met |
B |
| A |
|
|
|
3. |
INSPECT BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY |
Click here
| NG |
|
|
|
4. |
CHECK HARNESS AND CONNECTOR (BACK DOOR LOCK WITH COURTESY LIGHT SWITCH ASSEMBLY - MULTIPLEX NETWORK DOOR ECU AND BODY GROUND) |
(a) Disconnect the R14 back door lock with courtesy light switch assembly connector.
(b) Disconnect the R26 multiplex network door ECU connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
R14-6 (OPN) - R26-15 (POS) |
Always |
Below 1 Ω |
|
R14-1 (E) - Body ground |
Always |
Below 1 Ω |
|
R14-6 (OPN) or R26-15 (POS) - Body ground |
Always |
10 kΩ or higher |
| OK |
|
| NG |
|
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|