| Last Modified: 01-30-2024 | 6.11:8.1.0 | Doc ID: RM100000002FR2Q |
| Model Year Start: 2024 | Model: RAV4 | Prod Date Range: [10/2023 - ] |
| Title: PARK ASSIST / MONITORING: ULTRASONIC SENSOR (for Rear): INSTALLATION; 2024 MY RAV4 RAV4 HV [10/2023 - ] | ||
INSTALLATION
PROCEDURE
1. INSTALL ULTRASONIC SENSOR CUSHION SET
HINT:
Only perform this procedure when removing and installing the ultrasonic sensor cushion set.
(a) Install the ultrasonic sensor cushion set as shown in the illustration.
|
Install in this Direction |
- |
- |
2. INSTALL REAR CENTER ULTRASONIC SENSOR RETAINER
NOTICE:
- Installing the rear center ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
HINT:
- Perform the following procedure only when replacement of a rear center ultrasonic sensor retainer is necessary.
- Use the same procedure for the RH and LH side.
- The following procedure is for the LH side.
(a) Clean the rear bumper assembly surface.
(1) Remove any remaining double-sided tape from the rear bumper assembly.
(2) Wipe off any tape adhesive residue with cleaner.
(b) for TMC Made:
|
(1) Cover the sensor installation hole from the outside of the rear bumper cover with a 35 mm (1.38 in.) square piece of tape. |
|
(c) except TMC Made:
(1) Cover the sensor installation hole from the outside of the rear bumper cover with a 30 mm (1.18 in.) square piece of tape.
(d) Apply primer to the rear bumper assembly on the installation area of the rear center ultrasonic sensor retainer using a brush or felt.
NOTICE:
- Replace the brush or felt if it is dirty or has become hardened.
- Keep any painted surface free from primer.
- If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
- Do not touch surfaces to which primer has been applied until the rear center ultrasonic sensor retainer has been attached.
|
*A |
for TMC Made |
*B |
except TMC Made |
|
*C |
for LH Side |
*D |
for RH Side |
|
*a |
Scribed Line |
- |
- |
|
Primer Application |
- |
- |
(e) Let the primer dry sufficiently.
NOTICE:
Do not touch applied surfaces until the primer is dry.
Recommended drying time:
10 minutes or more (at 23°C (73°F))
(f) Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.
(g) Remove the peeling paper of the new rear center ultrasonic sensor retainer trying not to touch the adhesional surface.
NOTICE:
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work glove.
(h) Align the rear center ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.
NOTICE:
The application strength of the rear center ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
NOTICE:
w/ TMC Made:
- Make sure that the rear center ultrasonic sensor retainer is within the retainer mark-off line after installation.
- Make sure that the angle judgment ribs are within 5° above and below the angle judgment mark-off lines.
HINT:
- Apply pressure so that it does not lift up from the rear bumper assembly.
- Pushing force: 50 N (5.1 kgf) for 3 seconds
|
*A |
for TMC Made |
*B |
for LH Side |
|
*C |
for RH Side |
- |
- |
|
*a |
Retainer Mark-off Line |
*b |
Angle Judgment Rib |
|
*c |
Angle Judgment Mark-off Line |
- |
- |
|
*A |
except TMC Made |
- |
- |
|
*a |
Scribed Line |
- |
- |
3. INSTALL REAR CORNER ULTRASONIC SENSOR RETAINER
NOTICE:
- Installing the rear corner ultrasonic sensor retainer with some double-sided tape remaining may cause poor adhesion. Perform this procedure until the tape is sufficiently removed.
- Make sure to use a cloth when removing. Using a screwdriver, etc., may cause damage and poor adhesion.
HINT:
Perform the following procedure only when replacement of a rear corner ultrasonic sensor retainer is necessary.
(a) Clean the rear bumper assembly surface.
(1) Remove any remaining double-sided tape from the rear bumper assembly.
(2) Wipe off any tape adhesive residue with cleaner.
(b) for TMC Made:
|
(1) Cover the sensor installation hole from the outside of the rear bumper cover with a 35 mm (1.38 in.) square piece of tape. |
|
(c) except TMC Made:
(1) Cover the sensor installation hole from the outside of the rear bumper cover with a 30 mm (1.18 in.) square piece of tape.
(d) Apply primer to the rear bumper assembly on the installation area of the rear corner ultrasonic sensor retainer using a brush or felt.
NOTICE:
- Replace the brush or felt if it is dirty or has become hardened.
- Keep any painted surface free from primer.
- If the primer contacts a painted surface, it may leave light primer marks. Therefore, use protective tape when using liquid primer.
- Do not touch surfaces to which primer has been applied until the rear corner ultrasonic sensor retainer has been attached.
|
*A |
for TMC Made |
*B |
except TMC Made |
|
*C |
for LH Side |
*D |
for RH Side |
|
*a |
Scribed Line |
- |
- |
|
|
Primer Application |
- |
- |
(e) Let the primer dry sufficiently.
NOTICE:
Do not touch applied surfaces until the primer is dry.
Recommended drying time:
10 minutes or more (at 23°C (73°F))
(f) Confirm that the primer has completely dried by touching the rear bumper assembly. Then remove the tape.
(g) Remove the peeling paper of the new rear corner ultrasonic sensor retainer trying not to touch the adhesional surface.
NOTICE:
After removing the peeling paper, do not touch the surface of the tape with your fingers or cotton work glove.
(h) Align the rear corner ultrasonic sensor retainer with the scribed line on the rear bumper assembly and install it as shown in the illustration.
NOTICE:
The application strength of the rear corner ultrasonic sensor retainer will weaken if reapplied. If reapplication is necessary, be sure to replace it with a new one.
HINT:
- Apply pressure so that it does not lift up from the rear bumper assembly.
- Pushing force: 50 N (5.1 kgf) for 3 seconds
|
*A |
for TMC Made |
*B |
except TMC Made |
|
*C |
for LH Side |
*D |
for RH Side |
|
*a |
Scribed Line |
- |
- |
4. INSTALL REAR CENTER ULTRASONIC SENSOR
HINT:
- Use the same procedure for the RH and LH side.
- The following procedure is for the LH side.
(a) Attach the claw to install the rear center ultrasonic sensor.
NOTICE:
- When reusing the sensor, make sure that each sensor is returned to its original position.
- Check that the claw is securely fitted.
-
Do not push the microphone surface.
Microphone Surface
HINT:
Align the connector with the protrusion of the mark when connecting it.
|
*A |
for TMC Made |
*B |
except TMC Made |
|
*a |
Protrusion of the mark |
- |
- |
|
|
Install in this Direction |
- |
- |
|
(b) Connect the connector. |
|
5. INSTALL REAR CORNER ULTRASONIC SENSOR
HINT:
- Use the same procedure for the RH and LH side.
- The following procedure is for the LH side.
(a) Attach the claw to install the rear corner ultrasonic sensor.
NOTICE:
- When reusing the sensor, make sure that each sensor is returned to its original position.
- Check that the claw is securely fitted.
-
Do not push the microphone surface.
Microphone Surface
HINT:
Align the connector with the protrusion of the mark when connecting it.
|
*A |
for TMC Made |
*B |
except TMC Made |
|
*a |
Protrusion of the mark |
- |
- |
|
|
Install in this Direction |
- |
- |
|
(b) Connect the connector. |
|
6. INSTALL REAR BUMPER ASSEMBLY
Click here
![2024 MY RAV4 RAV4 HV [10/2023 - ]; EXTERIOR PANELS / TRIM: REAR BUMPER: INSTALLATION](/t3Portal/stylegraphics/info.gif)
7. CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (w/ Hands Free Power Back Door)
-
for A25A-FKS:
Click here
-
for A25A-FXS:
Click here
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
8. INSTALL BATTERY HOLE COVER (for HV Model, w/ Hands Free Power Back Door)
Click here
9. INSTALL REAR NO. 2 FLOOR BOARD (for HV Model, w/ Hands Free Power Back Door)
Click here
10. INSTALL DECK BOARD ASSEMBLY (for HV Model, w/ Hands Free Power Back Door)
Click here
11. INSPECT KICK DOOR CONTROL SENSOR (w/ Hands Free Power Back Door)
Click here
12. INITIALIZE POWER BACK DOOR SYSTEM (w/ Hands Free Power Back Door)
Click here
13. PERFORM CALIBRATION
(a) for HV Model:
Click here
(b) for Gasoline Model:
Click here
|
|