HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL; 2024 MY RAV4 HV [10/2023

Last Modified: 01-30-2024	6.11:8.1.0	Doc ID: RM100000002FR7F
Model Year Start: 2024	Model: RAV4 HV	Prod Date Range: [10/2023 - ]
Title: HYBRID / BATTERY CONTROL: HV RELAY ASSEMBLY (for NICKEL METAL HYDRIDE BATTERY): REMOVAL; 2024 MY RAV4 HV [10/2023 - ]

REMOVAL

CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during HV battery junction block assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced

Replaced Part or Performed Procedure	Necessary Procedures	Effect/Inoperative Function when Necessary Procedure not Performed
*: When performing learning using the Techstream. Click here
Auxiliary battery terminal is disconnected/reconnected	Perform steering sensor zero point calibration	Lane control system
		Parking support brake system*
		Pre-collision system
	Reset back door close position	Power back door system
	Back door lock initialization	Power door lock control system

CAUTION:

Orange wire harnesses and connectors indicate high-voltage circuits. To prevent electric shock, always follow the procedure described in the repair manual.
Click here
To prevent electric shock, wear insulated gloves when working on wire harnesses and components of the high voltage system.

NOTICE:

After the ignition switch is turned off, the audio and visual system records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 2 minutes before disconnecting the cable from the negative (-) auxiliary battery terminal.
When the cable is disconnected from the negative (-) auxiliary battery terminal and the security lock setting has been enabled, multi-display operations will be disabled upon next startup unless the password is entered. Be sure to check the security lock setting before disconnecting the cable from the negative (-) auxiliary battery terminal.

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work.

2. REMOVE SERVICE PLUG GRIP

Click here

3. DISCONNECT ENGINE ROOM MAIN WIRE

Click here

4. REMOVE CONNECTOR COVER ASSEMBLY

Click here

5. CHECK TERMINAL VOLTAGE

Click here

6. INSTALL CONNECTOR COVER ASSEMBLY

Click here

7. CONNECT ENGINE ROOM MAIN WIRE

Click here

8. REMOVE BENCH TYPE REAR SEAT CUSHION ASSEMBLY

Click here

9. REMOVE REAR SEAT CUSHION LOCK HOOK

Click here

10. REMOVE NO. 1 INDOOR ELECTRICAL KEY ANTENNA ASSEMBLY

Click here

11. REMOVE REAR DOOR SCUFF PLATE LH

Click here

12. REMOVE NO. 3 BATTERY SERVICE COVER BOARD

Click here

13. REMOVE REAR DOOR SCUFF PLATE RH

HINT:

Use the same procedure as for the LH side.

14. REMOVE NO. 2 BATTERY SERVICE COVER BOARD

Click here

15. REMOVE BATTERY SERVICE COVER BOARD

Click here

16. REMOVE REAR SEAT CUSHION LEG SUB-ASSEMBLY

Click here

17. REMOVE NO. 1 HV BATTERY COVER PANEL RH

Click here

18. DISCONNECT FLOOR UNDER WIRE

Click here

19. DISCONNECT FLOOR WIRE

CAUTION:

Be sure to wear insulated gloves.

(a) Disengage the clamp.

*a	Electric Vehicle Battery Plug Assembly Connector
*b	HV Battery Junction Block Assembly Connector

(b) Disconnect the electric vehicle battery plug assembly connector.

(d) Disengage the 2 clamps to disconnect the floor wire.

20. REMOVE NO. 1 HYBRID BATTERY EXHAUST DUCT

Click here

21. REMOVE UPPER HV BATTERY COVER SUB-ASSEMBLY

Click here

22. REMOVE HV BATTERY JUNCTION BLOCK ASSEMBLY

CAUTION:

Be sure to wear insulated gloves and protective goggles.

(a) Remove the bolt and disconnect the electric vehicle battery plug assembly.

(b) Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.

(d) Disengage the 2 claws and open the wiring harness protector.

(e) Disconnect the HV battery junction block assembly connector.

NOTICE:

Insulate the disconnected connectors with insulating tape.

(f) Using a screwdriver with its tip wrapped with protective tape, disengage the 2 claws and remove the wiring harness protector.

*a	Protective Tape

(g) Disconnect the HV battery junction block assembly connector.

(h) Remove the 4 nuts and HV battery junction block assembly from the HV battery.

NOTICE:

If the HV battery junction block assembly has been struck or dropped, replace it with a new one.