| Last Modified: 02-14-2025 | 6.11:8.1.0 | Doc ID: RM100000002Q1VQ |
| Model Year Start: 2025 | Model: RAV4 HV | Prod Date Range: [11/2024 - ] |
| Title: THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Entry Function, HV Model): Entry Exterior Alarm and Answer-back Buzzer do not Sound; 2025 MY RAV4 HV [11/2024 - ] | ||
|
Entry Exterior Alarm and Answer-back Buzzer do not Sound |
DESCRIPTION
The smart key system (for Entry Function) uses the wireless door lock buzzer to perform various vehicle exterior warnings. When the conditions of each warning are met, the certification ECU (smart key ECU assembly) sends a buzzer activation request signal to the main body ECU (multiplex network body ECU) via CAN communication and the buzzer sounds.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
- When using the Techstream with the power switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select the vehicle type under manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the Techstream and the vehicle.
-
The smart key system (for Entry Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
Click here
![2024 - 2025 MY RAV4 HV [10/2023 - ]; THEFT DETERRENT / KEYLESS ENTRY: SMART KEY SYSTEM (for Start Function, HV Model): HOW TO PROCEED WITH TROUBLESHOOTING](/t3Portal/stylegraphics/info.gif)
-
Before replacing the certification ECU (smart key ECU assembly) or main body ECU (multiplex network body ECU), refer to Registration.
Click here
- After repair, confirm that no DTCs are output.
PROCEDURE
|
1. |
CHECK CUSTOMIZE SETTING (WIRELESS BUZZER RESPONSE FUNCTION) |
(a) Connect the Techstream to the DLC3.
(b) Turn the power switch on (IG).
(c) Turn the Techstream on.
(d) Enter the following menus: Customize Setting / Wireless Door Lock.
Wireless Door Lock
|
Tester Display |
Description |
Default |
Setting |
ECU |
|---|---|---|---|---|
|
Wireless Buzzer Response Function |
Wireless buzzer response |
Enable |
$00:Disable,$01:Enable |
Main body ECU (multiplex network body ECU) |
|
Result |
Proceed to |
|---|---|
|
The customize setting is "Enable" |
A |
|
The customize setting is "Disable" |
B |
| B |
|
|
|
2. |
CHECK WIRELESS DOOR LOCK CONTROL SYSTEM |
(a) Check that the function operates normally.
Click here
|
Result |
Proceed to |
|---|---|
|
Wireless door lock function operates normally |
A |
|
Wireless door lock function does not operate normally |
B |
| B |
|
|
|
3. |
READ VALUE USING TECHSTREAM (EACH UNLOCK DETECTION SWITCH) |
(a) Enter the following menus: Body Electrical / Main Body / Data List.
(b) Read the Data List according to the display on the Techstream.
Body Electrical > Main Body > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
FR Door Lock Position Switch Status |
Front door RH unlock detection switch signal |
Lock or Unlock |
Lock: Front door RH locked Unlock: Front door RH unlocked |
- |
|
FL Door Lock Position Switch Status |
Front door LH unlock detection switch signal |
Lock or Unlock |
Lock: Front door LH locked Unlock: Front door LH unlocked |
- |
|
RR Door Lock Position Switch Status |
Rear door RH unlock detection switch signal |
Lock or Unlock |
Lock: Rear door RH locked Unlock: Rear door RH unlocked |
- |
|
RL Door Lock Position Switch Status |
Rear door LH unlock detection switch signal |
Lock or Unlock |
Lock: Rear door LH locked Unlock: Rear door LH unlocked |
- |
Body Electrical > Main Body > Data List
|
Tester Display |
|---|
|
FR Door Lock Position Switch Status |
|
FL Door Lock Position Switch Status |
|
RR Door Lock Position Switch Status |
|
RL Door Lock Position Switch Status |
OK:
The Techstream display changes correctly in response to the lock/unlock operation.
| NG |
|
GO TO LIGHTING SYSTEM (Proceed to Door Unlock Detection Switch Circuit) |
|
|
4. |
PERFORM ACTIVE TEST USING TECHSTREAM (WIRELESS BUZZER) |
(a) Enter the following menus: Body Electrical / Main Body / Active Test.
(b) Perform Active Test according to the display on the Techstream.
Body Electrical > Main Body > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Wireless Buzzer |
Wireless door lock buzzer |
OFF/ON |
- |
Body Electrical > Main Body > Active Test
|
Tester Display |
|---|
|
Wireless Buzzer |
|
Result |
Proceed to |
|---|---|
|
Wireless door lock buzzer does not sound |
A |
|
Wireless door lock buzzer sounds |
B |
| A |
|
| B |
|
|
|